led005r4 product information bulletin backlight led modules ?uniform illumination of channel letter signs ?long life: up to 100,000 hours depending on color?osram power topled ? allows high luminous flux ?120 viewing angle per led ?low profile (<5mm) allows installation where space is limited ?each module has 8 movable coupons connected with wires ?minimal heat generation ?wire interconnects allow flexible mounting. total length can be varied from 0.8 ft. to 1.8 ft. ?mounting hole allows easy installation by screw or snap-in spacers ? thr ee modules can be connected head to tail. up to six modules in series with power fed to the center of the strip ? many modules can be connected in parallel (limited only by power source capacity and ul considerations) ?listed in ul sign accessor y manual (sam) ? confor mally coated to protect against moisture and condensation (ip22) ? available as a system with matching optotronic ? power supplies (literatur e code ecs049) the osram sylvania backlight Can innovative alter native to neon and other conventional lighting. backlight modules offer alternatives to traditional neon sources. the main advantages of led backlight over neon or cold cathode sour ces ar e r educed manufacturing costs, durability, reduced maintenance costs, and small size. backlighting lamp modules are ideally suited to fit contours and cur ves typical to adver tising space and channel letters, and can be used for general signage applications too. theyar e available in red, yellow, true green, white, orange and blue. optotronic ? led power supplies from osram sylvania ar e specially designed to operate the backlight modules at 10.5v. a range of ul class 2 power supplies are available for indoor and outdoor, dry and damp location use. pr oduct a vailability product color backlite/633/os/lm03a/s super red backlite/615/os/lm03a/a amber red backlite/610/os/lm03a/o orange backlite/587/os/lm03a/y yellow backlite/525/0s/lm03a/t true green backlite/470/os/lm03a/b blue backlite/os/lm03a/w1 white backlite/os/lm03a/w2-854 white backlite/os/lm03a/w2-865 white application information applications backlighting advertising panels signs, channel letters, and displaysgeneral lighting application notes 1. small dimensions 2. shock r esistance 3. high color efficiency 4. dir ectional radiation characteristics 5. no ir/uv radiation 6. power supplies for operation
maximum ratings parameter symbol values units operating temperature* t op -30 +75 storage temperature range t stg -40+85 maximum voltage v max 11 v dc reverse voltage v r 11 v dc * temperature should be measured at the t c point on the module. (operating temperature for red, amber, orange and yellow modules is -40 to +85? dimensions length width mm (in) mm (in) smallest unit 30 (1.18) 30 (1.18) led grid 15 (0.59) cable 50 (1.97) dimensions on diagrams in mm, unless stated otherwise. cable (50mm) op t o s em i co n du c to r s os r am op t o s em i co n du c to r s os r am op t o s em i co n du c to r s os r am op t o s em i co n du c to r s os r am op t o s em i co n du c to r s os r am op t o s em i co n du c to r s os r am op t o s em i co n du c to r s os r am op t o s em i co n du c to r s os r am op t o se mi con du ct o rs osr am 0.8 ft. to 1.8 ft. 8 boar ds electrically connected tc point
safety information 1. the led module and its components should not be mechanically stressed. 2. assembly must not damage or destroy conducting paths on the circuit board. 3. to avoid mechanical damage to the connecting cables, the boards should be attached securely to the intended substrate. heavy vibration should be avoided. 4. detach each circuit board unit of the module only be severing the connecting cables (with power disconnected). 5. installation of led modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. only qualified personnel should be allowed to per for m installations. 6. correct electrical polarity needs to be observed. wrong polarity may destroy the module! 7. parallel connection is highly recommended for safe electrical operation mode. serial connection of more than 3 modules is not recommended. unbalanced voltage drop can cause hazardous overload and damage the led module. 8. electrical contact is achieved with the contact cables. a maximum of 3 modules can be installed consecutively fr om one power feed. operation with more than 3 consecutive backlight modules will reduce photometric performance and exceed the current carrying capacity of the module. if mor e than 3 modules ar e connected in series (maximum 6), power feed should be to the center of the string. 9. the module itself is protected against condensation water with a polymeric conformal coating. supplementary soldering on any solder pad will destr oy the confor mal coating and with it pr otection against condensation water . 10. operation in or under water is not allowed. assembly infor mation 1. mounting of the led module may be performed with screws or snap-in spacer (e.g. from richco www.richco-int.com) by using 4 mm holes in the circuit board. see the acklight intallation guide?or more details. 2. the mounting of the module is carried out by attaching it at the mounting holes. mounting screws should be used with synthetic washers to pr event cir cuit boar d damage and possible shor t cir cuiting. 3. a maximum of 3 modules can be installed consecutively from any power feed. installation with more than 3 backlight modules may take the form of, for example, either 6 modules installed consecutively with a power feed to the center or with a splitting of the power feed to contact groups of 3 modules. 4. to connect the led modules with each other or with optotronic power supply we recommend standard connectors (e.g. wago 243-214 or 224-201). 5. derate maximum led load for remote mounting or exterior applications. contact osram sylvania for details. the led module incorporates no protection against short circuits, overload or overheating. therefore it is necessary to operate the modules with an electronically stabilized power supply offering protection against the above mentioned safety risks. osram optotronic power supplies are specifically designed with protection features for safe operation. when using power supplies other than optotronic the following basic safety features should be verified in addition to any other application specific concerns and local safety codes: ?short circuit protection ?overload protection ?overheat protection ?correct output voltage, including consideration for ripple and spikes.
?2004 osram syl v ania printed on r ecycled paper . 11 /04 topled is a registered trademark of siemens aktiengesellschaft corporation. optotronic is a r egister ed trademark of osram gmbh used under license. osram is a registered trademark of osram gmbh. specifications subject to change without notice. osram syl vania national customer service and sales center 18725 n. union str eet westfield, in 46074 industrial & commercial phone: 1-800-255-5042 fax: 1-800-255-5043 national accounts phone: 1-800-562-4671 fax: 1-800-562-4674 oem/specialty markets phone: 1-800-762-7191 fax: 1-800-762-7192 photo-optic phone: 1-888-677-2627 fax: 1-800-762-7192 in canada osram sylvania ltd. headquar ters 2001 dr ew road mississauga, on l5s 1s4 industrial & commer cial phone: 1-800-263-2852 fax: 1-800-667-6772 special markets phone: 1-800-265-2852 fax: 1-800-667-6772 v isit our website: www .sylvania.com power supply ordering information optotronic ? 6w (51500) optotronic 25w (51505) optotronic 50w (51508, 51509) led item no. of max. no. of max. no. of max. number color modules* length (ft) modules* length (ft) modules* length (ft) 70081 super red 1 1.8 6 10.8 12 21.6 70011 amber red 1 1.8 6 10.8 12 21.6 70071 orange 1 1.8 6 10.8 12 21.6 70012 yellow 1 1.8 6 10.8 12 21.6 70013 true green 1 1.8 6 10.8 12 21.6 70014 blue 1 1.8 6 10.8 12 21.6 70045 white 1 1.8 7 12.6 14 25.2 70102 white (w2) 1 1.8 4 7.2 9 16.2 70103 white (w2) 1 1.8 4 7.2 9 16.2 * each module can be sub-divided into 8 coupons. ordering and specification information* wave length item ordering volts current viewing number (nm) or luminous number abbreviation color watts (v dc) (amps) angle of leds color temp. (k) flux (lm) 70081 backlite/633/os/lm03a/s super red 4.2 10.5 0.40 120 32 633 nm 54 70011 backlite/615/os/lm03a/a amber red 4.2 10.5 0.40 120 32 617 nm 54 70071 backlite/610/os/lm03a/o orange 4.2 10.5 0.40 120 32 606 nm 86 70012 backlite/587/os/lm03a/y yellow 4.2 10.5 0.40 120 32 587 nm 69 70013 backlite/525/os/lm03a/t true green 4.2 10.5 0.40 120 32 525 nm 57 70014 backlite/470/os/lm03a/b blue 4.2 10.5 0.40 120 32 470 nm 9 70045 backlite/os/lm03a/w1 white 3.4 10.5 0.32 120 32 x = 0.32; y =0.31 29 70102** backlite/os/lm03a/w2-854 white 5.3 10.5 0.50 120 32 5400k 69 70103** backlite/os/lm03a/w2-865 white 5.3 10.5 0.50 120 32 6500k 69 * all information relates to entire module with 32 leds. modules may be sub-divided into 8 coupons of 4 leds each. data r eflects statistical mean values. actual data may differ depending on variances in the manufacturing process. ** new product. contact osram sylvania for availability. ordering guide backlite / 470 / os / lm03a / b backlight module wavelength opto id no. color code 470 nm semiconductor b = blue
|
